How to make chemical DRP rice puller

Friends in today’s world a lot people cheat in the name of rice puller. Someone make it from vibrate someone from magnet and looting huge amount of money from people.

You also Do not trap in fake news and keep your mind open. This rice puller material is not purchased by anyone.

Today I will show you how to make rice puller by chemical. I already told you making rice puller by electronic method using television CTR board.

To make chemical rice puller you have to take copper more than 100gram and mixactive metal(it is not easily available in market)

Please check following metal seller website for mixactive metal

Step 1 – you have to boil mixactive metal in any oil for 20 minutes.
Step 2- you mix this metal with copper or paste it on upper part of copper.

Now you check rice will pull from 6 inch or more then that. Or Rice to Rice Pull approx 3 inch.
In 2 minutes rice colour will change to light brown
If you press rice it will turn in powder
It will attract anti iron from 3-4 inch. Torch will diffuse in 1 minute. You will wash it Any time it will function for 7 to 8 month.
I make this article for you because you will save from fraud people who will cheat you and looting money from you.
Thank you.

Revealing chemical DRP formula soon ( How to make chemical DRP or rice puller easy process)

Do you want to make your own chemical drp ?
keep checking this website to know
how to make chemical DRp ( chemical rice puller)

finally i got success in making chemical DRP.
My experiment Details
MR – 6
RR – 3.5
Torch – 5 inches (between 1 minutes)
rice color change.
Now making final powerful item.
I will write all the step by step procedure in my website soon.

Learn How to Make e-DRP.

Today I will explain how cheaters use electronic DRP  to show Metal to rice function.

(If you don’t know much about electronics take help with others, for any other information about this article contact on my whatsapp number +91-8279164546. Incoming blocked only Whatsapp.)

As i already  explained in the previous  posts, electrostatic force of metal can attract rice grains. By using electronics and remote control boards, a electronic DRP can be made. (To show MR, FIRE, PENCIL, SMOKE & with some drawbacks Needle test also)  Total budget of project is under 2000/- Rs.

Parts List

1) Step-up Power module high voltage generator ( click here to buy on
2) Remote control toy car  rechargeable  type   ( click here to buy on
3) Some wire
4) Small thin copper  metal sheet  5cm in diameter.


Step-up Power module 500 KV (500000 V)
Don’t touch the material while testing. It will not kill you, but gives you a shock. Even though voltage is high it delivers very low current.



First open the remote controlled to car, inside  it you will find one circuit board, two motors.
Remove all the parts from inside the car
Cut the connections of front motor in  the circuit board.
Cut the connections of LED front lights (some models comes without lights).
Now Remove the connections of back motor  ( not at the board).  Remove the motor by de-soldering  its  wires.
After doing all the above steps,  you will have
1) circuit board with battery power connections and a switch between battery pin & circuit board
2) Two wires disconnected from motor
3) A small metal antenna

click the image below

Don’t worry if your car  has different type of  circuit board.
You are going to use only one motor’s output . (After taking the circuit board out don’t forget  to solder antenna to circuit board otherwise remote will not work properly.)

In other words we are using 4.5 – 6 volts coming from board to back side motor,  to power up our  “step-up power”  module which can be controlled by remote of the toy car.

See the image below ,  click on image to zoom.

Wrap some electrical insulation tape on one output wire of step-up power module. We are going to use only one high voltage output wire. Make sure that insulated wire with electrical tape is away from all other connections. Now solder the high voltage output wire ( non insulated one) to circular shaped metal plate.

After making all connections  fix all this circuit ( car circuit board & step-up power module without touching each other) in to smallest plastic box possible leaving  battery pin outside the box. And fix  switch to the box.
Now fix the circular metal plate downside to the plastic box.
Battery connecting pin  & switch should be on upside.

If you place this device inside  any copper material ( bowl, vessel, chembu etc),  the circular shaped copper metal should  touch the material’s base.  Now cover the remaining gap inside the material with cotton or papers.   Now your electronic DRP is ready, place it on a table or paper on ground. Take remote and press FORWARD  button  ( if it not works press BACK button).  If you do all the above process correctly it will attract rice grains from 6 Inches minimum.  It can bend candle flame, agarbathi smoke from one inch distance minimum.

Note: For best results  use medium sized copper material.

There are many techniques to show this fake functions. In the next post ( may be next week)  I will show another technique without using any device inside the material.


Today I will show you how cheaters in rice puller bussiness cheat customers by showing fake metal to rice function of fake rice puller packed in box. (Here iam only discussing one technique, in the next post i will show some more techniques)

Many people who try to cheat people will say that, they have original rice puller in packing.
They will show you a box and to give function test, they will insert a copper wire in to a hole drillled to that box. If you put rice grains near that copper wire it will attract rice grains.

Actually they use
Flyback transformer from a CRT T.V circuit board
Voltage multiplier etc
but now, a device is available to show this function test when fake material is placed in the box. Along with the fake material, they place that device inside the box , they will connect a wire from that device to the hole drilled. When they insert copper wire to give function test from outside it touches the inside wire.